Module điều khiển Motion 4 trục tốc độ cao (cho XP-8000/WP-8000 PAC) ICP DAS I-8094-G
Features
- Independent 4-axis motion control
- Support for hand wheel and jog functions
- 2/3-axis linear / 2-axis circular interpolation function
- Continuous interpolation function
- Programmable T/S-curve acceleration and deceleration
- A maximum pulse output rate of 4 Mpps for each axis
- Pulse Output Types: CW/CCW or PULSE/DIR
- 32-bit encoder counter for each axis
- Encoder Pulse Input Types: A/B Phase or Up/Down
- Programmable automatic homing for each axis
- Position comparison management and software limits
- A wide range of synchronous actions (event-triggered actions)
Introduction
The I-8094 and I-9094 are 4-axis stepping/pulse-type servo motor control modules that can be used on the programmable automation controller (PAC) series provided by ICPDAS, and are suitable for general-purpose motion applications. In addition to their wide speed range, these intelligent motion controllers also have a variety of motion control functions built in, such as 2/3-axis linear interpolation, 2-axis circular interpolation, T/S-curve acceleration/deceleration, a range of synchronous actions, automatic homing, and others.
A major advantage is that the majority of the I-8094/I-9094 motion control functions are performed by the high-performance motion ASIC with little load on the processor. While driving the motors, the motion status, and the status of other I/O channels on the PAC modules, can still be monitored. As the CPU loading requirements of the I-8094/I-9094 is minimal, one or more motion modules may be used with a single PAC controller. ICP DAS also provides a wide range of functions and examples that can be used to reduce the need for additional programming, making it a highly cost-effective solution for motion control application developers.
Features
![]() |
![]() |
![]() |
![]() |
![]() |
|
Specifications
| Number of Axes | 4 |
| Maximum Pulse Output Rate | 4 MHz |
| Command Type | Pulse Command |
| Resolution | 32-bit |
| Pulse Output Mode | CW/CCW, PULSE/DIR |
| Operation Mode | Semi-closed Loop |
| Linear Interpolation | Any 2 to 3 of 4 axes |
| Circular Interpolation | Any 2 axes |
| Speed Curve Profile | T/S-curve |
| Motion Relative I/O | Home, LMT+/-, NHOME, EMG, INP, ALM, SVON |
| Synchronous Action | 10 activation factors and 14 actions |
| Ring Counter Mode | 32-bit |
| Position Control Mode | Incremental mode and Absolute mode |
| Position Compare Trigger | 10 KHz |
| Encoder Interface | A/B pulse, Up/Down |
| Encoder Counter | 32-bit |
| Encoder Rate | 4 MHz |
| Digital Input Channels | – |
| Digital Output Channels | – |
| I/O Isolation (with DN-8468) | 2500 Vrms optical isolation |
| Connector | 68-pin SCSI-II connector |
| Power Consumption | +5 V @ 500 mA |
| Environmental | |
| Operating Temperature | -20 ~ +75°C |
| Storage Temperature | -30 ~ +85°C |
| Ambient Relative Humidity | 5 ~ 90% RH, non-condensing |
Ordering information
| I-8094-G | High-speed 4-axis Motion Control Module (For XP-8000/WP-8000 PAC) |
| I-9094 | High-speed 4-axis Motion Control Module (For XP-9000/WP-9000 PAC) |
Accessories
| DN-8468UB | Photo-isolated Universal Snap-on Wiring Terminal Board |
| DN-8468GB | Photo-isolated General Purpose Wiring Terminal Boar |
| DN-8468MB | Photo-isolated Snap-on Wiring Terminal Board for Mitsubishi MELSERVO-J2 Servo Amplifier |
| DN-8468PB | Photo-isolated Snap-on Wiring Terminal Board for Panasonic MINAS A4/A5 Servo Amplifier |
| DN-8468YB | Photo-isolated Snap-on Wiring Terminal Board for Yaskawa Sigma II/III/V Servo Amplifier |
| DN-8468DB | Photo-isolated Snap-on Wiring Terminal Board for Delta ASDA-A Servo Amplifier |
| DN-8468FB | Photo-isolated Snap-on Wiring Terminal Board for Fuji FALDIC-W Servo Amplifier |
| CA-SCSI15-H2 | 68-pin SCSI-II Male-Male Connector Cable, Length 1.5 M |
| CA-SCSI30-H2 | 68-pin SCSI-II Male-Male Connector Cable, Length 3.0 M |
| CA-SCSI50-H2 | 68-pin SCSI-II Male-Male Connector Cable, Length 5.0 M |





