Bộ chuyển đổi J1939 sang Modbus RTU Slave ICP DAS GW-7228
The GW-7228 is a solution that provides a protocol conversion between J1939 and Modbus RTU. For J1939 network, the GW-7228 supports PDU1, PDU2, broadcast and destination specific type of J1939 messages. From the view of Modbus RTU network, the GW-7228 is a Modbus RTU slave to reply the request from Modbus RTU master. We provide Utility software for users to configure the parameters of J1939 / Modbus RTU of the GW-7228. The application fields can be Diesel power-train applications, In-Vehicle networks for trucks and buses, etc.
The following figure shows the application architecture for the GW-7228

Applications
|
![]() |
Features
-
Provide PWR / J1939 / MODBUS indication LED
-
Built-in jumper to select 120 ohm terminal resister
-
Watchdog inside
J1939 Features
-
Transmission and reception of all types of J1939 messages, including PDU1, PDU2, broadcast and destination specific
-
J1939 Transport Protocol for transmission and reception of large messages (9 – 1785 bytes)
-
Supported BAM of Connection Management Message
-
Network addresses management
Modbus RTU Features
-
Support RS-232, RS-485 and RS-422
-
interfacesSupported Modbus RTU slave protocol
-
Configurable for Modbus Network ID(1~250)
-
Configurable baud rates of 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps
-
Configurable for no, odd, or even parity and 1 or 2 stop bits
-
Support Function Code 03 / 04 / 06 / 16 of Modbus functions for reading and writing J1939 Messages
Utility
-
Provide Modbus network configuration interface
-
Provide J1939 network configuration interface – Network Address / Device Name…
-
Provide J1939 Input / Output configuration interface

Comparison Table
ICP DAS Fieldbus Gateways Comparison Table:
|
Support Protocol
|
GW-7228
|
GW-7433D
|
I-7231D
|
I-7232D
|
I-7241D
|
I-7242D
|
|
J1939
|
CANopen Master
|
CANopen Slave
|
CANopen Slave
|
DeviceNet Slave
|
DeviceNet Slave
|
|
|
Modbus RTU Slave
|
Modbus TCP server/RTU Slave
|
DCON Master
|
Modbus RTU Master
|
DCON Master
|
Modbus RTU Master
|
|
|
Comm.
Interface |
RS-232
RS-422 RS-485 |
RS-232
RS-485 Ethernet |
RS-232
RS-485 |
RS-232
RS-485 |
RS-232
RS-485 |
RS-232
RS-485 |
|
Support Protocol
|
I-7243D
|
GW-7243D
|
GW-7552
|
GW-7553
|
HART-710
|
|
DeviceNet Master
|
DeviceNet Slave
|
PROFIBUS DP-V0 Slave
|
PROFIBUS DP-V0 Slave
|
HART Master
|
|
|
Modbus TCP server
|
Modbus TCP/RTU/
ASCII Master |
Modbus RTU/ASCII
Master/Slave |
Modbus
TCP/RTU/ASCII Master/Slave |
Modbus RTU/ASCII
Slave |
|
|
Comm.
Interface |
Ethernet
|
RS-232
RS-485 Ethernet |
RS-232
RS-422 RS-485 |
RS-232
Ethernet |
RS-232
RS-422 RS-485 |
Hardware Specifications
|
Hardware
|
|
|
J1939 Port Channels
|
1
|
|
CAN Interface
|
|
|
Transceiver
|
NXP 82C250
|
|
Connector
|
9-pin D-sub connector
|
|
Baud Rate (bps)
|
250k
|
|
Isolation
|
3000 VDC power protection on CAN side, 2500Vrms photo-couple isolation on CAN bus
|
|
Terminator Resistor
|
Selectable 120Ω terminator resistor by jumper
|
|
Specification
|
ISO-11898-2, CAN 2.0A and CAN 2.0B
|
|
Pin Assignment
|
C.I.A. DS-102 (CAN_H=7, CAN_L=2)
|
|
UART Interface
|
|
|
Connector
|
14-pin screw terminal connecter
|
|
COM1
|
RS-232(TXD, RXD, GND)/RS-422(Tx+, Tx-, Rx+, Rx-)/ RS-485(D+, D-)
|
|
Baud Rate (bps)
|
2400, 4800, 9600, 19200, 38400, 57600, 115200
|
|
LED
|
|
|
Round LED
|
PWR / J1939 / MODBUS
|
|
Power
|
|
|
Power supply
|
+10 ~ +30 VDC
|
|
Power Consumption
|
1.5 W
|
|
Dip Switch
|
Init (Firmware Update) / Normal (Firmware Operation)
|
|
Mechanism
|
|
|
Installation
|
DIN-Rail
|
|
Dimensions
|
108mm x 72mm x 35mm (H x W x L)
|
|
Environment
|
|
|
Operating Temp.
|
-25 ~ 75 ℃
|
|
Storage Temp.
|
-30 ~ 80 ℃
|
|
Humidity
|
10 ~ 90% RH, non-condensing
|
Ordering Information
|
GW-7228 CR
|
J1939/Modbus RTU Slave Gateway included CA-0910 cable(RoHS)
|
Optional Accessories
| CA-0910-C |
9-pin Female D-sub & 3-wire CAN bus cable (1M)
|
| CNT-CAN |
CAN bus Connector
|
| SG-770 |
7/14 channel Surge Protector
|
| 4PCD-002 |
EMI Ferrite Split/Snap-On Core
|
| M12A-5P-IP68 |
Field-Installation A-coded 5-pin Female
|

