Bộ điều khiển IR 10 kênh đầu ra Relay kết nối Modbus RTU ICP DAS IR-310-RM
Features
-
10 channels high power relays: 10A x 4, 5A x 6
-
Supports IR commands (custom:64, built-in:32) for relay control.
-
NO & NC terminals for each channel
- Protection circuit for each channel
-
Sequential relay control
-
Supports maximum 5 sets of interlocked relay pairs (e.g. CW/CCW motor control)
-
Power-on values and power failure memory
-
RS-232 and RS-485 serial interface
-
Supports Modbus/RTU protocol (Slave)
-
Modbus Network IDs: 1 ~ 15 (HW); 1 ~ 247 (SW)
Introduction
IR-310-RM is a 10-channel high power relay module designed for the power control of various appliances. The relay module can switch up to 10 A loads. There are NO/NC switches and protection circuit for each channel. The relays can be controlled independently or sequentially by serial communication with Modbus RTU protocol, as well as by wireless IR remote control. There are also maximum 5 interlocked relay pairs for interlocked switching. The application field can be manual/automatic power switch, light scenario control and energy conservation etc.
Application
-
e-Classroom service
-
Lighting Scenario Control
-
Home and Building Automation
Utility
IR utility (contains IR-310-RM utility) is the configuration tool for IR-310-RM.
-
Can get/set separate or all settings from/to IR-310-RM.
-
For relay test and relay states indication.
-
Control IR-310-RM to emit IR commands for the IR learning remote.
Hardware Specification
|
Relay Output
|
||
|
Number of Outputs
|
10
|
|
|
Relay Types
|
Form C relay SPDT
|
|
|
Contact Rating
|
5A @220VAC for RL0, RL1 & RL6~RL9
10A @220VAC for RL2 ~ RL5 (Operating temperature: 25°C) |
|
|
Operating Time(Max.)
|
10 ms for RL0,RL1 & RL6 ~ RL9,
15 ms for RL2 ~ RL5 |
|
|
Release Time(Max.)
|
5 ms for RL0, RL1 & RL6 ~ RL9
10 ms for RL2 ~ RL5 |
|
|
Dielectric Strength
|
Open Contact
|
750VAC for RL0, RL1 & RL6 ~ RL9 1000VAC for RL2 ~ RL5 |
|
Contact & Coil
|
1500VAC for RL0, RL1 & RL6 ~ RL9 2500VAC for RL2 ~ RL5 |
|
|
Insulation Resistance
|
100 M Ohm min. at 500 VDC for RL0, RL1 & RL6 ~ RL9
1000M Ohm min. at 500VDC for RL2 ~ RL5 |
|
|
Life TIme
|
Mechanical : 1 × 10^7 OPS
Electrical : 1 × 10^5 OPS |
|
|
Serial Interface
|
||
| COM1 | RS-232 (TxD, RxD, GND) | |
| COM2 | RS-485 (DATA+, DATA-) | |
|
Format
|
Parity: None, Databits: 8, Stopbits: 1
|
|
|
Baud Rate
|
9600 ~ 115200 bps
|
|
| Protocol | Modbus/RTU (Slave) | |
|
Modbus Net ID
|
Hardware: 1 ~ 15; Software: 1 ~ 247
|
|
|
IR interface
|
||
|
IR input
|
On-board IR receiver
|
|
| 3.5 mm audio jack (for CA-IR-001) | ||
| IR Remote Commands |
64 IR commands (#0 ~ #63) corresponding to self-defined relay states.
32 IR commands (#192 ~ #223) corresponding to built-in relay states. |
|
|
LED Display
|
||
|
1 LED as power indication
|
||
|
10 LEDs as relay output indicators
|
||
|
Power
|
||
|
Power Supply
|
+ 12 VDC
|
|
|
Power Consumption
|
6.5W (max)
|
|
|
Mechanical
|
||
|
Dimensions(W x H x L)
|
220 mm x 48 mm x 113 mm
|
|
|
Environmental
|
||
|
Operating Temperature
|
-25 to +75°C
|
|
|
Storage Temperature
|
-30 to +80°C
|
|
|
Humidity
|
10 to 90%, non-condensing
|
|
Ordering Information
|
IR-310-RM CR
|
IR Controlled 10-channel High Power Relay Module (RoHS)
|
|---|