Module truyền thông 1 cổng DeviceNet Master ICP DAS I-8124W

Module truyền thông 1 cổng DeviceNet Master ICP DAS I-8124W

The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is an especially suit for networking “intelligent” devices as well as sensors and actuators within a system or sub-system. In CAN network, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted. As standalone CAN controller, I-8124W can represent an economic solution of DeviceNet application and be a DeviceNet master device in the CAN bus on the DeviceNet network. It is a “Predefined Master connection Set”, and supports Group 2 only Server functions to communication with slave devices. It has a independent CAN bus communication port with 5-pin screw terminal connector, and has the ability to cover a wide range of DeviceNet applications. Besides, I-8124W uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function. It can be installed in WinPAC or ViewPAC series PAC.It is popularly applied in the industrial automation, building automation,vehicle, marine, and embedded control network. In order to expand the DeviceNet functions of ICPDAS products, I-8124W module is developed for this purpose.

Applications

	CVD DeviceNet Application( Traditional Chinese) CVD DeviceNet Application( English )
	Communicate with PowerFlex400(English)
	SMC Valve Aplications(English) IFC-125 Valve Aplications(English) MKS FRCA Valve Aplications(English)
	SICK Distance Sensor Aplications(English)

Architecture

Features

• 3 indication LEDs (Error,Status,Bus LEDs)
• Programmable master MAC ID
• Programmable transfer-rate 125K, 250K, 500K
• Support maximum nodes up to 64
• Support Group 2 and UCMM functions
• The maximum Fragment number is (Input/Output) up to 64
• Support I/O Operation Mode: Poll, Bit-Strobe and Change Of State/Cyclic
• Support auto-scan slave device function
• Support on-line add device into and remove device from network
• Support auto-reconnect when the connection is broken

We have communicated with the following DeviceNet slaves

Memory Map of Remote I/O

There exist two memory areas, “Input Area” and “Output Area”. The input data of all DeviceNet slaves would be stored in the “Input Area” by DeviceNet master scan engine. Oppositely, the output data of those DeviceNet slaves would be in the “Output Area”. Please refer to the following figure.

Users can read a bulk data from “Input Area” in the DeviceNet Master module, like PISO-DNM100U or I-8124W. This bulk data contains multiple devices’ input statuses. If one of the input status of the remote DeviceNet slave changes, the corresponding data located in the “Input Area” would change immediately. Oppositely, the “Output Area” contains multiple devices’ output data. Users may change the output value of a certain device by changing the corresponding data located in the “Output Area”.

Software Utility Features

This utility supports to search all devices and specific devices in the network. These functions help the users to configure the connection of the slave devices. Anymore, the software also can diagnose the remote slave devices when building the DeviceNet network.

This software supports the users to configure the I/O connection of the devices by searching devices or manual setting. After configuring the I/O connection, the information would be saved into the EEPROM. The users can export the data from the EEPROM easily. Correspondingly, the users can import the data into the EEPROM.

The software utility can easily to access the I/O data of all the slave devices. The users can monitor the input data of the specific slave device and change the output data to the remote slave device with this utility.

Software

Item	Description
InduSoft Driver	The IndoSoft is one of the famous and high performance SCADA. Nowaday, it supports the CAN, CANopen and DeviceNet driver for all the coresponding converter or master series products. [more…]

Hardware Specifications

SUpport MCU

WinPAC Series

• WP-8141
• WP-8441
• WP-8841

ViewPAC Series

• VP-23W1
• VP-25W1

Ordering Informations

Optional Accessories