Nguồn tổ ong DC/DC 200W từ 9VDC~ 144VDC ra 1 kênh 5V- 12V-24V Leyu SD-200
Thông số kĩ thuật
| SPECIFICATION | ||||||||
| OUTPUT | ||||||||
| Model |
SD-200B |
SD-200C |
||||||
| DC Voltage |
5V |
12V |
24V |
48V |
5V |
12V |
24V |
48V |
| Rated Current |
34A |
16.7A |
8.4A |
4.2A |
40A |
16.7A |
8.4A |
4.2A |
| Current Range |
0~34A |
0~16.7A |
0~8.4A |
0~4.2A |
0~40A |
0~16.7A |
0~8.4A |
0~4.2A |
| Rated Power |
170W |
200.4W |
201.6W |
201.6W |
200W |
200.4W |
201.6W |
201.6W |
| Ripple & Noise |
100mVp-p |
120mVp-p |
150mVp-p |
200mVp-p |
100mVp-p |
120mVp-p |
150mVp-p |
200mVp-p |
| Voltage Adj. Range |
4.5 ~ 5.5VDC |
11 ~ 16VDC |
23 ~ 30VDC |
43 ~ 53VDC |
4.5 ~ 5.5VDC |
11 ~ 16VDC |
23 ~ 30VDC |
43 ~ 53VDC |
| Voltage Tolerance |
±2.0% |
±1.0% |
±1.0% |
±1.0% |
±2.0% |
±1.0% |
±1.0% |
±1.0% |
| Line Regulation |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
| Load Regulation |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
| Setup, Rise Time | 300ms, 50ms at full load | |||||||
|
|
||||||||
| INPUT |
|
|||||||
| Voltage Range | B:19 ~ 36VDC C:36 ~ 72VDC D:72 ~144VDC | |||||||
| Efficiency |
79% |
82% |
85% |
86% |
81% |
84% |
86% |
86% |
| DC Current |
10.8A/24V |
10.6A/24V |
10.4A/24V |
10.4A/24V |
5.4A/48V |
5.2A/48V |
6.7A/48V |
5A/48V |
| Inrush Current | C:45A/48VDC D:45A/96VDC | |||||||
| PROTECTION | ||||||||
| Over Load
|
105 ~ 135% rated output power | |||||||
| Protection type: Shut down o/p voltage, re-power on to recover | ||||||||
| Over Voltage |
5.75 ~ 6.75V |
16.8 ~ 20V |
31.5 ~ 37.5V |
53 ~ 65V |
5.75 ~ 6.75V |
16.8 ~ 20V |
31.5 ~ 37.5V |
53 ~ 65V |
| Protection type: Shut down o/p voltage, re-power on to recover | ||||||||
| Over Temperature | 95℃±5℃(100℃±5℃ for SD-200B-12 only) TSW1 detect on main power transistor | |||||||
| Protection type: Shut down o/p voltage, recovers automatically after temperature goes down | ||||||||
| ENVIRONMENT | ||||||||
| Working Temp. | -20 ~ +60℃(Refer to “Derating Curve”) | |||||||
| Working Humidity | 20 ~ 90% RH non-condensing | |||||||
| Storage Temp., Humidity | -40 ~ +85℃, 10 ~ 95%RH | |||||||
| Temp. Coefficient | ±0.03%/℃ (0 ~ 50℃) | |||||||
| Vibration | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | |||||||
| SAFETY & EMC | ||||||||
| Safety Standards | UL60950-1approved(for SD-200C-24 type only), IEC60950-1 CB approved by TUV (for D type only) | |||||||
| Withstand Voltage | I/P-O/P: 1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC | |||||||
| Isolation Resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃ / 70% RH | |||||||
| EMC Emission | Compliance to EN55022 (CISPR22) Class B | |||||||
| EMC Immunity | Compliance to EN61000-4-2,3,4,6,8, light industry level, criteria A | |||||||
| OTHERS | ||||||||
| Dimension | 215*115*50mm (L*W*H) | |||||||
| Weight | 1.1Kg | |||||||
| Packing | 12pcs/14.4Kg/0.92CUFT | |||||||
| NOTE | ||||||||
| 1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives. |
||||||||