Nguồn tổ ong DC/DC 100W từ 9VDC~ 144VDC ra 1 kênh 5V- 12V-24V Leyu SD-100
Thông số kĩ thuật
| SPECIFICATION | |||||||||||||||
| OUTPUT | |||||||||||||||
| Model |
SD-100A-5 |
SD-100B-5 |
SD-100D-5 |
SD-100B-12 |
SD-100C-12 |
SD-100D-12 |
SD-100B-24 |
SD-100C-24 |
SD-100D-24 |
SD-100B-48 |
SD-100C-48 |
SD-100D-48 |
|||
| DC Voltage |
5V |
12V |
24V |
48V |
|||||||||||
| Rated Current |
20A |
8.5A |
4.2A |
2.1A |
|||||||||||
| Current Range |
0~20A |
0~8.5A |
0~4.2A |
0-2.1A |
|||||||||||
| Rated Power |
100W |
102W |
100.8W |
100.8W |
|||||||||||
| Ripple&Noise |
100mVp-p |
120mVp-p |
150mVp-p |
150mVp-p |
|||||||||||
| Voltage Adj.Range |
4.5~5.5VDC |
11~16VDC |
23~30VDC |
43.2-52.8VDC |
|||||||||||
| Voltage Tolerance |
±2.0% |
±1.0% |
±1.0% |
±1.0% |
|||||||||||
| Line Regulation |
±0.5% |
±0.3% |
±0.2% |
±0.2% |
|||||||||||
| Load Regulation |
±0.5% |
±0.3% |
±0.2% |
±0.2% |
|||||||||||
| Setup, Rise Time | 2s,50ms(only D mode) at full load | ||||||||||||||
| Hold Up Time | 20ms(only D mode) at full load | ||||||||||||||
| INPUT | |||||||||||||||
| Voltage Range | A：9.2~18VDCB:19~36VDC C:36~72VDC D:72~144VDC or 85~132VAC | ||||||||||||||
| Efficiency |
74% |
75% |
76% |
75% |
77% |
80% |
78% |
81% |
83% |
78% |
81% |
83% |
|||
| DC Current |
4.8A/18V |
2.4A/24V |
1.8A/96V |
4.8A/24V |
2.4A/48V |
1.8A/96V |
4.8A/24V |
2.4A/48V |
1.8A/96V |
4.8A/24V |
2.4A/48V |
1.8A/96V |
|||
| Inrush Current | D:18A/96VDC | ||||||||||||||
| Leakage Current | <0.75mA/120VAC(SD-100D) | ||||||||||||||
| PROTECTION | |||||||||||||||
| Over Load | 105~135% rated output power | ||||||||||||||
| Protection type: Hiccup mode,recovers automatically after fault condition is removed | |||||||||||||||
| Over Voltage |
5.75~6.75V/10%load |
16.8~20V/10%load |
31.5~37.5V/10%load |
60.2-79.2/10%load |
|||||||||||
| Protection type:Hiccup mode,recovers automatically after fault condition is removed | |||||||||||||||
| ENVIRONMENT | |||||||||||||||
| Working Temp. | -10~+60℃ (Refer to“Derating Curve”) | ||||||||||||||
| Working Humidity | 20~90%RH non-condensing | ||||||||||||||
| Storage Temp.,Humidity | -20~+85℃,10~95%RH | ||||||||||||||
| Temp.Coefficient | ±0.03%/℃ (0~50℃) | ||||||||||||||
| Vibration | 10~500Hz,2G 10min./1cycle,60min.each along X, Y, Z axes | ||||||||||||||
| SAFETY &EMC | |||||||||||||||
| Safety Standards | IEC60950-1CB approved by TUV(for D type only) | ||||||||||||||
| Withstand Voltage | I/P-O/P:1.5KVAC I/P-FG:2.0KVAC O/P-FG:0.5KVAC | ||||||||||||||
| Isolation Resistance | I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500VDC /25℃ /70%RH | ||||||||||||||
| EMC Emission | Compliance to EN55022(CISPR22) Class B | ||||||||||||||
| EMC Immunity | Compliance to EN61000-4-2,3,4,6,8,light industry level,criteria A | ||||||||||||||
| OTHERS | |||||||||||||||
| Dimension | 199*98*38mm(L*W*H) | ||||||||||||||
| Weight | 0.55Kg | ||||||||||||||
| Packing | 30pcs/16.5Kg | ||||||||||||||
| NOTE | |||||||||||||||
| 1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. |
|||||||||||||||