Card PCI 1 cổng DeviceNet Master ICP DAS PISO-DNM100U-T

Card PCI 1 cổng DeviceNet Master ICP DAS PISO-DNM100U-T

PISO-DNM100 can represent an economic solution of DeviceNet application and be a DeviceNet master device on the DeviceNet network. It is a “Predefined Master-Slave connection Set”. PISO-DNM100 supports Group 2 only Server and UCMM functions to communication with slave devices. It has an independent CAN bus communication port and has the ability to cover a wide range of DeviceNet applications.

Besides, PISO-DNM100 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function.It can be installed on almost any windows-based system, for example Windows system. It is popularly applied in the industrial automation, building automation, vehicle, marine, and embedded control network. In order to expand the DeviceNet functions of ICPDAS products, PISO-DNM100 is developed for this purpose.

Application

	The production & Inspection of the LCD panel (Traditional Chinese)
	Communicate with PowerFlex400(English)
	SMC Valve Aplications(English) IFC-125 Valve Aplications(English) MKS FRCA Valve Aplications(English)
	SICK Distance Sensor Aplications(English)

Hardware Features

• DeviceNet Version: Volume I & II, Release 2.0
• Programmable master MAC ID and baud rate
• Baud Rate: 125 kbps, 250 kbps, 500 kbps
• Support Group 2 and UCMM connection
• I/O Operating Modes: Poll, Bit-Strobe, Change of State / Cyclic
• I/O Length: max 512 input bytes and 512 output bytes pre slave
• Slave Node : 63 nodes max
• Support auto-search slave device function
• Support on-line adding and removing devices
• Support auto-detect Group 2 and UCMM device
• Auto-reconnect when the connection is broken
• LED: Status,ERR

Firmware Features

• Programmable Master MAC ID
• Programmable transfer-rate 125 kbps, 250 kbps, 500 kbps
• Each port support maximum nodes up to 64
• Support Group 2 Only Server functions
• Support UCMM functions
• Predefined Master-Slave Connection Set
• The maximum Fragment number is (Input/Output) up to 64
• Support I/O Operation Mode: Poll, Bit-Strobe and Change Of State/Cyclic
• Support Auto-Scan slave device function
• Support on-line adding and removing devices
• Support boot-up auto communicating with slave devices
• Support Auto-Reconnect when the connection is broken

We have communicated with the following DeviceNet slaves

Memory map of Remote I/O

There exist two memory areas, “Input Area” and “Output Area”. The input data of all DeviceNet slaves would be stored in the “Input Area” by DeviceNet master scan engine. Oppositely, the output data of those DeviceNet slaves would be in the “Output Area”. Please refer to the following figure.

Users can read a bulk data from “Input Area” in the DeviceNet Master module, like PISO-DNM100U or I-8124W. This bulk data contains multiple devices’ input statuses. If one of the input status of the remote DeviceNet slave changes, the corresponding data located in the “Input Area” would change immediately. Oppositely, the “Output Area” contains multiple devices’ output data. Users may change the output value of a certain device by changing the corresponding data located in the “Output Area”.

Software Utility Features

This utility supports to search all devices and specific devices in the network. These functions help the users to configure the connection of the slave devices. Anymore, the software also can diagnose the remote slave devices when building the DeviceNet network.

This software supports the users to configure the I/O connection of the devices by searching devices or manual setting. After configuring the I/O connection, the information would be saved into the EEPROM. The users can export the data from the EEPROM easily. Correspondingly, the users can import the data into the EEPROM.

The software utility can easily to access the I/O data of all the slave devices. The users can monitor the input data of the specific slave device and change the output data to the remote slave device with this utility.

Software 

Item	Description
InduSoft Driver	The IndoSoft is one of the famous and high performance SCADA. Nowaday, it supports the CAN, CANopen and DeviceNet driver for all the coresponding converter or master series products. [more…]

Performance Test

DeviceNet for LabVIEW Application Tool

In order to develop complex DeviceNet applications, we provide a LabVIEW driver for this purpose. The PISO-DNM100(U) LabVIEW driver is the function reference to the DeviceNet master. We provide many useful VI functions in the LabVIEW environment. We also have the “DeviceNet Master Utility” to configure the DeviceNet hardware in your PC. The users not only operate easily and develop application rapidly, but also reduce the complexity of applications. The users can communicate with the remote DeviceNet devices in a few simple steps and need not to know about the detail of the DeviceNet protocol. It is the best tool to develop various distributed systems and other industrial applications software on DeviceNet network.

Hardware Specifications

Ordering Informations

Optinal Accessories