Module Control Dimmer 1 kênh ICP DAS LC-221/DIN
Features
- Power Relay Output
- Isolated AC Digital Input
- Isolated Analog Output For Control Dimming Ballast
- Supports Modbus RTU and DCON Protocols
- 2500 VDC Intra-Module Isolation
- +/-4 kV ESD Protection
- Tiny form-factor with easy screw mounting
Introduction
The LC-221 is an easy-to-use dimming ballast control module that requires no specialist skills to install and operate. It provides two methods of controlling the brightness of fluorescent lamps via a dimmer, either via digital input or a host controller. The digital input can directly control the light value from 10% to 100% luminous fl ux in sequence, without requiring a remote host controller. 4 kV ESD protection and 2500 VDC intra-module isolation are also provided. When required, communication with the LC-221 is programmable based on the Modbus RTU protocol, and an added benefit is that different addresses can be set for Modbus RTU communication via hardware configuration.
Applications

I/O Specifications
| Analog Output | |
| Channels | 1 |
| Type | 0 ~ 20 mA, 4 ~ 20 mA, 0 ~ 10 V, 1 ~ 10 V |
| Resolution | 12-bit |
| On Level | Close to GND |
| Accuracy | +/-0.1% of FSR |
| DA Output Response Time | 10 ms |
| Voltage Output Capability | 20 mA |
| Current Load Resistance | 450 Ω |
| Digital Input | |
| Channels | 1 |
| Type | Wet |
| On Voltage Level | 85 VAC ~ 240 VAC |
| Off Voltage Level | 45 VAC Max. |
| Input Impedance | 68 KΩ, 1 W |
| Relay Output | |
| Channels | 1 |
| Type | Power Relay, Form A (SPST N.O.) |
| Operating Voltage | 250 VAC or 30 VDC |
| Max. Load Current | 16 A (Res. load) |
| Operate Time | 15 ms Max. |
| Release Time | 5 ms Max. |
| Mechanical Endurance | 10,000,000 OPS |
| Electrical Endurance | 50,000 OPS |
| Power-on and Safe Value | Yes, programmable |
System Specifications
| Communication | |
| Interface | RS-485 |
| Format | N, 8, 1 |
| Baud Rate | 1200 ~ 115200 bps |
| Protocol | DCON, Modbus RTU |
| Node Addresses | 64 ~ 95 |
| Connector | RJ-11 (6P4C or 6P6C) |
| LED Display | |
| Power | 1 LED as Power Indicator |
| Isolation | |
| Intra-module Isolation, Field-to-Logic | 2500 VDC |
| EMS Protection | |
| ESD (IEC 61000-4-2) | ±4 kV contact for each Terminal |
| ±4 kV Air for Random Point | |
| EFT (IEC 61000-4-4) | ±4 kV for Power |
| Power | |
| Reverse Polarity Protection | Yes |
| Powered from Terminal Block | Yes, 10 ~ 30 VDC |
| Consumption | 1.4 W Max. |
| Mechanical | |
| Dimensions (W x L x H) | 52 mm x 98 mm x 27 mm |
| Installation | Screw Mounting |
| Environment | |
| Operating Temperature | -25°C ~ +75°C |
| Storage Temperature | -30°C ~ +80°C |
| Humidity | 10 ~ 95% RH, Non-condensing |
Ordering Information
| LC-221 CR | 1-channel Dimmer Control Module (RoHS) |
| LC-221/DIN CR | 1-channel Dimmer Control Module (DIN Rail mount) (RoHS) |
Accessories
| tM-7520U CR | RS-232 to RS-485 converter (RoHS) |
| tM-7561 CR | USB to RS-485 converter (RoHS) |
| I-7514U CR | 4-channel RS-485 Hub (RoHS) |
| TPD-280 CR | 2.8” Touch HMI device with RS-485 (RoHS) |
