Module RS-485 Modbus RTU 1 kênh đầu vào AC + 1 kênh đầu ra Relay điều khiển điện chiếu sáng ICP DAS LC-101/DIN
Features
- Cost-effective for lighting control
- Power Relay Output
- Isolated AC Digital Input
- Tiny form-factor
- Low power consumption
Introduction
The LC-101 is an easy-to-use lighting control module that requires no specialist skills to install and operate, and no software is needed in order to control the DO channels.
The LC-101 provides 1 channel for digital input (photo couple isolation) and 1 channel for relay output. The output channel is form C type relay, while the input channel is based on a sink-type using a wire connection. The input channel can directly control the relay ON and OFF sequence without requiring a remote host controller. 4 kV ESD protection and 5000 Vrms intra-module isolation are also provided.
When required, communication with the LC-101 is programmable based on the Modbus RTU protocol, and an added benefit is that different addresses can be set for Modbus RTU communication via hardware configuration.
Applications

I/O Specifications
| Digital Input | |
| Input Channels | 1 |
| Type | 90 ~ 240 VAC |
| On Voltage Level | 85 VAC |
| Off Voltage Level | 60 VAC |
| Input Impedance | 68 KΩ, 1 W |
| Isolation | 5000 Vrms |
| Function | Local and Remote Direct Control Relay ON/OFF and Remote Status Monitoring |
| Relay Output | |
| Output Channels | 1 |
| Type | Power Relay, Form C |
| Operating Voltage | 250 VAC or 30 VDC |
| Max. Load Current | NO: 10 A, NC: 6 A |
| Operating Time | 15 ms Max. |
| Release Time | 5 ms Max. |
| Electrical Life (Resistive load) | 100,000 ops |
| Mechanical Life | 20,000,000 ops at no load (300 ops/minute) |
| Power-on Value | No |
| Safe Value | No |
System Specifications
| Communication | |
| Interface | RS-485 |
| Format | N, 8, 1 |
| Baud Rate | 1200 ~ 115200 bps |
| Protocol | Modbus RTU/DCON |
| Node Addresses | Hardware Configuration: 32 ~ 63 Software Configuration: 0~255 for DCON and 1~247 for Modbus RTU standard) |
| Connector | RJ-11(6P4C or 6P6C) |
| LED Display | |
| Power | 1 LED as Power Indicator |
| EMS Protection | |
| ESD (IEC 61000-4-2) | ±2 kV Contact for Each Terminal |
| ±4 kV Air for Random Point | |
| EFT (IEC 61000-4-4) | ±2 kV for Power |
| Power Requirements | |
| Input Voltage Range | 10 ~ 30 VDC |
| Consumption | 0.5 W Max. |
| Connector | RJ-11 |
| Mechanical | |
| Dimensions (W x L x H) | 52 mm x 98 mm x 27 mm |
| Installation | Screw Mounting |
| Environment | |
| Operating Temperature | -25°C ~ +75°C |
| Storage Temperature | -30°C ~ +75°C |
| Humidity | 10 ~ 95% RH, Non-condensing |
Ordering Information
| LC-101 CR | 1-channel AC Digital Input and 1-channel Relay Output Lighting Control Module (screw mount) (RoHS) |
| LC-101/DIN CR | 1-channel AC Digital Input and 1-channel Relay Output Lighting Control Module (DIN Rail mount) (RoHS) |
Accessories
| tM-7520U CR | RS-232 to RS-485 converter (RoHS) |
| tM-7561 CR | USB to RS-485 converter (RoHS) |
| I-7514U CR | 4-channel RS-485 Hub (RoHS) |
| TPD-280 CR | 2.8” Touch HMI device with RS-485 (RoHS) |
