Module CANopen Slave 8 kênh đầu ra xung PWM + 8 kênh đầu vào bộ đếm tốc độ cao HSC ICP DAS CAN-2088C
CANopen is one kind of the network protocols based on the CAN bus and mainly used for embedded network of machine control, such as industrial machine control , aircraft engines monitoring, factory automation, medical equipments control, remote data acquisition, environmental monitoring, and packaging machines control, etc.
CAN-2084C module follows the CiA-301 version 4.02. CAN-2084C has passed the validation of the CiA CANopen conformance test tool. Therefore, you can use it with standard CANopen master easily by applying the EDS file. The CAN-2084C is a 4/8-channel Counter/Frequency module that provides “Up Counter”, “Frequency”, “Up/Down Counter”, “Dir/Pulse Counter” and “A/B Phase Counter” modes. It provides a variety of measurement applications, such as measuring a number of time-related quantities, counting events or totalizing and monitoring position with quadrature encoders. In addition, a digital filter is used to eliminate the effects of noise. By owing to the CANopen masters of ICP DAS, you can quickly build a CANopen network to approach your requirements. For more information about the CANopen master interfaces and other CANopen products, please refer to the following web site.
Applications


Hardware Specifications
|
CANopen Interface
|
|
|
NMT
|
Slave
|
|
Error Control
|
Node Guarding protocol / Heartbeat Producer
|
|
No. of PDOs
|
10Rx , 10Tx
|
|
PDO Modes
|
Event Triggered, Remotely requested, Cyclic and acyclic SYNC
|
|
PDO Mapping
|
Available
|
|
No. of SDOs
|
1 server, 0 client
|
|
Emergency Message
|
yes
|
|
CANopen Version
|
DS-301 v4.02
|
|
Device Profile
|
DSP-401 v2.1
|
|
Specification
|
ISO-11898-2, CAN 2.0A
|
|
Baud Rate (bps)
Setting by Rotary Switch |
10K, 20K, 50K, 125K, 250K, 500K, 800K, and 1M
|
|
Node ID |
1 ~ 99
|
|
Terminator Resistor
|
Switch for 120 Ω terminator resistor
|
|
Connector
|
5-pin screwed terminal block (CAN_GND, CAN_L, CAN_SHLD, CAN_H, CAN_V+)
|
|
EDS file
|
Provide default EDS file
|
|
PWM
|
|
|
Channels
|
8 (Source)
|
|
Output Max. Load Current
|
1 mA
|
|
Frequency
|
0.2 Hz ~ 500 kHz (non-continuous)
|
|
Scaling Resolution
|
16-bit (1 ~ 128 μs for each step)
|
|
Duty Cycle
|
0.1 ~ 99.9 %
|
|
PWM Mode
|
Burst mode, Continuous mode
|
|
Burst mode counter
|
1~65535 counts
|
|
Trigger Mode
|
Hardware (Start and Stop) or Software (Start and Stop)
|
|
Intra-module Isolation
|
2500 Vrms
|
|
ESD Protection
|
4 kV Contact for each channel
|
|
Digital Input
|
|
|
Channels
|
8 (Sink)
|
|
ON Voltage Level
|
+5.5 ~ +30 V
|
|
OFF Voltage Level
|
<3.5 V
|
|
Counter Frequency
|
500 kHz Max.
|
|
Max. Counts
|
32-bits (4,294,967,295)
|
|
Input Impedance
|
2.2 kΩ, 0.5 W
|
|
Intra-module Isolation
|
2500 Vrms
|
|
ESD Protection
|
4 kV Contact for each channel
|
|
LED
|
|
|
CANopen Status
|
3 LEDs for PWR/RUN/ERR
|
|
Terminal Resister
|
1 LED as Terminal Resister indicators
|
|
PWM LED
|
8 LEDs as PWM Output indicators
|
|
DI LED
|
8 LEDs as Digital Input indicators
|
|
Power
|
|
|
Power Supply
|
Unregulated +10 ~ +30 VDC
|
|
Power Consumption
|
2 W
|
|
Mechanism
|
|
|
Installation
|
DIN-Rail
|
|
Dimensions
|
32.3 mm x 99 mm x 77.5 mm ( W x L x H ) Detail
|
|
Environment
|
|
|
Operating Temp.
|
-25 ~ +75 ℃
|
|
Storage Temp.
|
-30 ~ +80 ℃
|
|
Humidity
|
10 ~ 90% RH, non-condensing
|
Ordering Infomation
|
CAN-2088C
|
CANopen module of 8-channel PWM and 8-channel High Speed Counter |
Related Products
| PISO-CAN200/200U | 2-Port Isolated Protection CAN Communication Board |
| PISO-CAN400/400U | 4-Port Isolated Protection CAN Communication Board |
| PEX-CAN200i (PISO-CAN200E) |
PCI Express CAN Communication Card |
| PISO-CM100U | One Standalone Intelligent CAN Communication Card |
| PISO-CPM100U | One Standalone Intelligent CANopen Communication Card |
