Module USB 10 kênh đầu vào số + 8 kênh đầu ra Relay cách ly ICP DAS USB-2068-18
Introduction
The USB-2068-18 is an 8-channel Form C relay output and 10-channel digital input module with the USB interface. All digital input channels can be used as 32-bit counters. In addition, the digital input channels can be selected as sink/source type and dry/wet contact via wire connections. There are also options for configuring power-on and safe values. 8 kV ESD protection(for all channels) and 3750 VDC intra-module isolation(for digital input channels) are also provided to enhance noise protection capabilities in industrial environments.
Compare with traditional PC I/O card, it is waste of time to open chassis and configure I/O board. In ICP DAS USB I/O, you will enjoy the simply controlling I/O in the efficient way. ICP DAS USB I/O equips USB bus powered feature, one cable to access I/O and provide power without additional power wiring.
Compare with traditional PC I/O card, it is waste of time to open chassis and configure I/O board. In ICP DAS USB I/O, you will enjoy the simply controlling I/O in the efficient way. ICP DAS USB I/O equips USB bus powered feature, one cable to access I/O and provide power without additional power wiring.
Features
- 10-channel digital input and 8-channel relay output.
- Dry Contact and Wet Contact Selectable via Wire Connections
- All Digital Input Channels can used as 32-bit Counters
- Form C Relay Output
- 8kV ESD protection
- Wide Operating Temperature Range
- 3000 VDC Intra-Module Isolation
- USB 2.0 Full-Speed
- USB Bus Powered
- Lockable USB cable
- Driver Free
Application
- Automation
- Measurement and testing
- Laboratory research
Software
USB-2K Utility
USB-2K Utility provides a simple way to easily test and instant acquire data for all ICP DAS USB IO series modules without programming.
- USB module configuration
- I/O configuration
- Log Data analysis
- Easy to test

VB/C++/C#.NET/VB.NET SDK
ICP DAS provides a SDK for USB I/O modules to help user to develop own project easily and quickly. The SDK can be supported in VB/C++/C#.NET/VB.NET to fulfill project development.

Specification
| Relay Output | ||
| Channels | 8 | |
| Output Type | Form C | |
| Contact Rating (Resistive Load) | 0.25 A @ 250 VAC 0.24 A @ 220 VAC |
|
| 2 A @ 30 VDC | ||
| Operate Time | 3 ms (typical) | |
| Release Time | 4 ms (typical) | |
| Insulation Resistance | 109 Ω at 500VDC | |
| Dielectric Strength | Between Open Contact | 1000 Vrms (1 min.) |
| Between Coil and Contacts | 1500 Vrms (1 min.) | |
| Endurance | Mechanical | 1 x 108 ops |
| Electrical | 2 x 105 ops (at 30 V / 2 A) | |
| Power On Value | Yes | |
| Safe Value | Yes | |
| Digital Input / Counter | ||
| Channels | 10 | |
| TypeDry Contact | Close to GND | |
| Wet Contact | Sink/Source | |
| On Voltage Level | +10 ~ 50 VDC | |
| Off Voltage Level | +4 VDC Max. | |
| Counters | Max. Count | 4294967295 (32-bit) |
| Max. Input Frequency | 500 Hz | |
| Min. Pulse Width | 1ms | |
| Input Impedance | 10 KΩ | |
| Overvoltage Protection | 70 VDC | |
| Communication | ||
| Interface | USB 2.0 Full-Speed | |
| Watchdog | 1 Hardware watchdog (1.6 second) | |
| 1 Software watchdog (Programmable) | ||
| LED Indicators | ||
| System LED Indicators | 3 LEDs as Power, Run and Error | |
| I/O LED indicators | Yes, 12 LEDs Digital Input/ Relay Output Indicator | |
| Isolation | ||
| Intra-Module Isolation, Field-to-Logic | 3000 VDC | |
| EMS Protection | ||
| ESD (IEC 61000-4-2) | 8 kV contact for each terminal | |
| 16 kV air for random point | ||
| Mechanical | ||
| Dimensions (W x L x H) | 31 mm × 129 mm × 147mm | |
| Environmental | ||
| Operating Temperature | -25 ~ +75 °C | |
| Storage Temperature | -40 ~ +85 °C | |
| Humidity | 10 ~ 95% RH, non-condensing | |
| Power | ||
| Power Consumption | 2.3 W (Max.) | |
Ordering information
| USB-2068-18 | 10-channel Digital Input, 8-channel Relay Output Module |
