Bộ đổi nguồn tổ ong AC/DC 100W từ 220Vac sang 24V DC 4.5A Leyu NES-100-24
Thông số kĩ thuật
SPECIFICATION | |||||||||||||
OUTPUT | |||||||||||||
Model |
NES-100-5 |
NES-100-7.5 |
NES-100-9 |
NES-100-12 |
NES-100-15 |
NES-100-24 |
NES-100-48 |
||||||
DC Voltage |
5V |
7.5V |
9V |
12V |
15V |
24V |
48V |
||||||
Rated Current |
20A |
13.6A |
11.2A |
8.5A |
7A |
4.5A |
2.3A |
||||||
Current Range |
0~20A |
0~13.6A |
0~11.2A |
0~8.5A |
0~7A |
0~4.5A |
0~2.3A |
||||||
Rated Power |
100W |
102W |
100.8W |
102W |
105W |
108W |
110.4W |
||||||
Ripple&Noise |
80mVp-p |
120mVp-p |
120mVp-p |
120mVp-p |
120mVp-p |
120mVp-p |
150mVp-p |
||||||
Voltage Adj. Range |
4.75~ 5.5V |
7.13 ~ 8.3V |
8.55 ~ 9.9V |
11.4 ~ 13.2V |
14.25 ~ 16.5V |
22.8 ~ 26.4V |
45.6 ~ 52.8V |
||||||
Voltage Tolerance |
±2.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
±1.0% |
||||||
Line Regulation |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
||||||
Load Regulation |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
||||||
Setup,Rise Time | 500ms, 20ms/230VAC 500ms, 20ms/115VAC at full load | ||||||||||||
Hold Up Time | 30ms/230VAC 25ms/115VAC at full load | ||||||||||||
INPUT | |||||||||||||
Voltage Range | 85 ~ 132VAC / 176 ~ 264VAC selected by switch 248 ~ 373VDC | ||||||||||||
Frequency Range | 47 ~ 63Hz | ||||||||||||
Efficiency |
80% |
81% |
81% |
83% |
84% |
86% |
86% |
||||||
AC Current | 2A/115VAC 1.2A/230VAC | ||||||||||||
Inrush Current | Cold Start36A | ||||||||||||
Leakage Current | <2mA / 240VAC | ||||||||||||
PROTECTION | |||||||||||||
Over Load | 110 ~ 150% rated output power | ||||||||||||
Protection type: Hiccup mode, recovers automatically after fault condition is removed | |||||||||||||
Over Voltage |
5.75~6.75V |
8.6 ~ 10.1V |
10.4 ~ 12.2V |
13.8~16.2V |
17.25~20.25V |
27.6~32.4V |
55.2~64.8V |
||||||
Protection type: Hiccup mode, recovers automatically after fault condition is removed | |||||||||||||
ENVIRONMENT | |||||||||||||
Working Temp. | -20 ~ +60℃ (Refer to “Derating Curve”) | ||||||||||||
Working Humidity | 20 ~ 90% RH non-condensing | ||||||||||||
StorageTemp., Humidity | -40 ~ +85℃, 10 ~ 95% RH | ||||||||||||
Temp. Coefficient | ±0.03%/℃ (0 ~ 50℃) | ||||||||||||
Vibration | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | ||||||||||||
SAFETY &EMC | |||||||||||||
Safety Standards | Design refer to UL60950-1, CB(IEC60950-1),CCC GB4943 | ||||||||||||
Withstand Voltage | I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC | ||||||||||||
Isolation Resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃ / 70% RH | ||||||||||||
EMC Emission | Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3 | ||||||||||||
EMC Immunity | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-1, light industry level, criteria A | ||||||||||||
OTHERS | |||||||||||||
Dimension | 159*97*38mm (L*W*H) | ||||||||||||
Weight | 0.55Kg | ||||||||||||
Packing | 40pcs/carton | ||||||||||||
NOTE | |||||||||||||
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance: includes set up tolerance, line regulation and load regulation. 4. Line regulation is measured from low line to high line at rated load. 5. Load regulation is measured from 0% to 100% rated load. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives. |